Step 0:
First, connect to the power supply, the LED panel shows “OFF”, the ceiling vibrator is in the OFF state.
Step 1: Click The Power On Button
Click the “Power on” button of the remote controller. When it clicked, the ceiling vibrator is on, but it does not start working immediately.
Step 2: Choose Mode
F1 is displayed on the LED panel after completing the first step. F1 means that it is currently in F1 mode.
The ceiling vibrator has nine modes, F1~F9; each mode means as follows:
- F1, default mode, keep working, shut down after 15 minutes.
- F2, working 10 seconds, pause 10 seconds…working 10 seconds, pause 10 seconds…repeat…shutdown after 30 minutes.
- F3, working 30 seconds, pause 30 seconds…working 30 seconds, pause 30 seconds…repeat…shut down after 1 hour.
- F4, working 1 minute, pause 1 minute…working 1 minute, pause 1 minute…repeat…shut down after 2 hours.
- F5, working 2 minutes, pause 2 minutes…working 2 minutes, pause 2 minutes…repeat…shut down after 4 hours.
- F6, working 5 minutes, pause 5 minutes…working 5 minutes, pause 5 minutes…repeat…shut down after 6 hours.
- F7, working 10 minutes, pause 10 minutes…working 10 minutes, pause 10 minutes…repeat…shut down after 12 hours.
- F8, working 20 minutes, pause 20 minutes…working 20 minutes, pause 20 minutes…repeat…shut down after 24 hours.
- F9, working 30 minutes, pause 30 minutes…working 30 minutes, pause 30 minutes…repeat…randomly shutdown between 1-4 hours.
You can click the “Mode+” button to switch mode.
Step 3: Choose Level
After choosing the mode, click the “Level+” or “Level-” to choose the working strength of the vibrator.
At this time, the LED panel shows P1-P9. P1 is the weakest, and P9 is the strongest.
Step 4: Function(Start Working)
Click on the function button: “Knocking”, “Vibrating”, or “Knocking + Vibrating”. The ceiling vibrator will start working in the mode/level/function you just chose.
When the vibrator is working, the L/U/H character will be displayed on the LED panel:
- L – Knocking function
- U – Vibrating function
- H – Knocking + Vibrating function
Step 5: Power Off
Clicking the “Power off” button, the ceiling vibrator will stop working and return to the OFF state.
Optional Step: Timing
You can timing the ceiling vibrator before “Step 5: Power Off” and let it start working after 1-9 hours.
First, you need to get the vibrator in working condition, vibrating, knocking, or vibrating and knocking.
Then, click the “Timing” button to enter the appointment mode. At this time, the LED panel will display E1.
E1 means the ceiling vibrator will start working after 1 hour. Click the timing button again to switch between E1 to E9.
- E1: start working after 1 hour.
- E2: start working after 2 hours.
- …
- E9: start working after 9 hours.
Then, click the “Timing on” button to start the timer, then the led panel will start blinking.
If you want to cancel the timings, click the “Cancel Timing” button.
Automatic Noise Sensing Function
V3 version is based on V2 version (without Bluetooth) to add auto-sensing function and improve product quality.
You can divide the functional area of the remote control into two parts.
Among them, the upper half is all the functions of the V2 version, and the arrangement of the buttons is the same. Please refer to the V2 version remote control described above.
The bottom half is the functions of the V3 version with auto-sensing. Yes, there are only two buttons, and it is easy to use.
Noise Sensing Vibration
When you click the Noise Sensing On button, the LED panel will display 111 and a small red dot will blink. This means that the current noise sensing vibration mode will automatically open the vibration mode when the device senses the noise.
Noise Sensing Knocking
If you click the Noise Sensing On switch again, the LED panel will display 222 and a small red dot will blink. This means that the current noise sensing knocking mode will automatically open the knocking mode when the device senses the noise.
Noise Sensing Vibration + Knocking
Then, if you click the Noise Sensing On switch again, the LED panel will display 333 and a small red dot will blink. This means that the current noise sensing vibration + knocking mode will automatically open the knocking mode when the device senses the noise.
Turn Off The Noise Sensing Function
The functions turned on and off by V2 version and V3 version are independent of each other. If you find a small red dot blinking, then it means the current noise sensing function is activated, you still need to click the off button at the bottom right corner of the remote control to turn off the noise sensing function.
The noise sensing function cannot be turned off if you only click the off button in the upper right corner of the remote control.
When you click the Noise Sensing Off button, the LED panel will display 000 and no small red dot blinking.
The above is the detailed instruction of V2 version and V3 version. If you still have other questions, please contact us.